Pages

7.5.19

Mr Croc - egg carton crocodile


This craft is very similar to the lizard we made last time, so it's all about cutting and stacking, the tricky part is finding enough egg cartons!!

You will need:
3 x Large (dozen) egg cartons or
6 Regular (half a dozen) egg cartons
Pencil
Scissors
Craft glue
Glue stick (optional)
Green paint
Sheet of plain paper
Black marker or gel pen

1. Mr Croc is made from twelve of the middle cones you find in egg cartons.

If you can get hold a few of the larger cartons, you'll get 5 cones per box, rather than the usual two. 

Of course you could always make a smaller crocodile with less, and spread the cones out more, or add in extra cones (if you have them) for a really long tail!

1. We painted our cones first, while they were still in the egg cartons, but you could assemble your croc and paint him at the end if you prefer. 

If you're painting at the start, remember to paint some of the egg box lid green too, for the feet.


2. Cut the cones out roughly, in a strip, then separate them by snipping a part. We cut out 12 altogether. 

LEAVE ONE OF THESE ROUGHLY CUT OUT CONES TO THE SIDE FOR LATER (FOR THE HEAD).


3. Then cut around the bottom of the 11 remaining cones, just above the cardboard joins - so the edges are nice and even. (I've used a pen to mark above the card join on this cone, to show where to cut).





4. Aim to make them look the same size (but don't worry if they're not exactly alike! And you can always tidy them up if you feel you need to, at the stacking stage)

Put one of these trimmed cones aside too (for the end of the tail) so you're now left with 10. 

Then chop about 1cm off the top of the 10 remaining cones, by squeezing the cone sides together and snipping across the top. The cut will look a bit wonky when you squeeze the cone back into shape, but that's fine as you won't see them when you stack your Croc together.



5. Now the fun part, the stacking! We stacked 5 cones together for the body.

Brush glue around the inside edges of the first cone, then push the next one in, but don't push it in too far, you want to have spaces between the ridges (and this stretches out the body too). Brush glue around the inside edge of the second cone and add the third, and so on. Keep the spacing looking even (keep trying different cones to get a good fit or trim a bit more if you need to).


6. The next cone is going to go in facing the opposite way (so you can attach the tail), but it's too big as it is, so you need to shorten it by cutting about 1cm off the bottom edge, (see photo above), then glue inside the body.

7. Cut about 1cm off the bottom of the remaining 4 cones too.

(You should still have 2 cones left aside, for the head and bottom of the tail)


8. Glue and stack these four pieces on top of the cone you've just attached to the body section, but make the gaps wider apart than those on the body - this will allow you to extend the tail and to curve it slightly, if you want to. Brush glue inside the pieces you're adding to the tail, concentrating on where the cones are most in contact with each other.

9. For the end of the tail, take the trimmed cone (from step 4) that you've been saving, and cut it in half lengthways, and glue one in place.



10. For the head, take the last remaining cone you cut out roughly at the very beginning, and hold it so you're looking at one of the flat sides. This will be the top of your croc's head. 

On the top of the head, close to the edge of the cone, use a pencil to draw two curved, sticky out eyes, starting from each corner. Join with a line in the middle. (See the photo) Roughly draw around the rest of the cone, from the bottom of one eye, around the back, to the bottom of the other. 


When cutting out, it might help to cut down each corner first, to the pencil line, fold all but the front flap out, and cut these three side and back flaps off.

On the front, cut between Mr Croc's eyes first, to the line, before snipping this little piece away (or tucking it inside the head). Then round off the eyes.

11. Paint them yellow.


12. While they're drying, draw a thin strip on some plain paper (for the teeth) - about 12cm long and roughly 0.5cm wide.

With a fine black pen, draw a zigzag line from the top to the bottom line, before cutting this strip out.

Use the pen to finish off the eyes and to add nostrils. We drew long, thin triangles for the pupils.



13. Snip one end into a tapered 'V', rub with glue stick, or brush on a thin layer of glue, and stick the start of the teeth in place. Wrap around his face, until it looks even on the other side and snip another 'V'.




Glue the head to the body.

14. For the feet, cut a 2-3cm strip and round it at one end. Use this as a template to draw around, and cut out four. Draw on claws and glue them on, angled forward, under the body.